Cat C32 ACERT Marine Propulsion Engine (EPA Tier 3)

Cat C32 ACERT Marine Propulsion Engine (EPA Tier 3)

Cat C32 ACERT Marine Propulsion Engine (EPA Tier 3)

The C32 ACERT marine propulsion engine is available at ratings that meet both EPA Tier 3 and IMO II emissions regulations. It has a separate circuit aftercooling system (SCAC) for A through C ratings and a seawater aftercooling system (SWAC) for D and E ratings. The C32 ACERT has seven ratings with Wide Operating Speed Range (WOSR) and extended oil change intervals. Other benefits include proven engine operating history and performance iron with thousands of validation testing hours for quality and durability. The C32 ACERT marine engine is supported by the extensive Cat global dealer network and standard warranty.

Power Rating
Power Range
750-1800 bhp (559-1342 bkW)
Engine Specifications
Speed Range
1600-2300 rpm
Emissions
EPA Tier 3, IMO II, EU IW
Aspiration
TTA
Bore
5.71in
Stroke
6.38in
Displacement
1959in³
Rotation from Flywheel End
Counterclockwise
Configuration
Vee 12, 4-Stroke-Cycle Diesel
Dimensions & Weights
Maximum Height
62.5in
Minimum Length
77.8in
Minimum Height
60.9in
Maximum Width
60.17in
Maximum Length
83.5in
Minimum Dry Weight
6950lb
Minimum Width
60.17in

Standard Equipment:

Air Inlet System
  • Separate Circuit After-Cooled (SCAC)
  • Seawater After-Cooling (SWAC) System
  • Air cleaner
  • Turbochargers, jacket water cooled
  • Turbochargers inlet, 152 mm (6 in) OD straight connection
 
Control System
  • Programmable Low Idle (550 - 750 rpm)
  • WOSR (Wide Operating Speed Range) available for - A, B, & C Ratings
  • Programmable High Idle Limit for WOSR Ratings
  • Electronic diagnostics and fault logging
  • Engine and transmission monitoring (speed, temperature, pressure)
  • Electronic fuel/air ratio control
  • Engine Protection Mode for extended ambient conditions
  • Torque Limiting functionality for WOSR ratings only
  • 70-pin customer connector
  • Throttle Input signal options
 
Cooling System
  • Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines
  • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
  • SCAC pump, gear driven
  • Jacket water pump, gear driven
  • Sea water pump, bronze impeller, gear driven, for HEX cooled engines only
  • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard
  • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Seawater After-Cooling (SWAC) System
 
Exhaust System
  • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
  • Water-cooled exhaust manifold & turbocharger
 
Flywheels & Flywheel Housings
  • SAE standard rotation (CCW facing exciter end)
  • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
 
Fuel System
  • Duplex Fuel Filters, Spin-on, RH & LH service
  • Fuel connections size:Supply JIC 37 Deg -10 (7/8-14), Return JIC 37 Deg -8 (3/4-16)
  • Plate Type Fuel Cooler installed behind Aftercooler Shunt Tank
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design
 
Lube System
  • Simplex Oil Filters, RH or LH service
  • Deep sump oil pan
  • RH or LH service oil filler locations
  • RH or LH service dipstick
  • Oil pump, gear driven
 
Mounting System
  • Front support - adjustable
 
Power Take-offs
  • Front Poly-V groove pulley (Quantity 1) for auxiliary drives
 
General
  • Common electrical bonding point
  • Engine does not ship with zinc components
 

Optional Equipment:

Air Inlet Systems
  • Air Inlet Cleaner
  • Air Inlet Adapter
 
Charging Systems
  • Battery Charger
  • Charging Alternators
  • Ammeter
 
Cooling System
  • Marine Gear/Transmission Oil Coolers
  • Connections
 
Exhaust System
  • Dual Elbow
  • Flexible Fitting
  • Dual Muffler
  • Muffler Spark Arresting
  • Flange
 
Fuel System
  • Water Separator
 
Instrumentation
  • OEM Wiring Harness
  • Engine to Engine Harness
  • Instrument Panels
  • Exhaust Temperature Sensors
  • Wiring Harness
  • Gauges
  • Transmission Sensors
 
Lube System
  • Transmission Oil Cooler
  • Manual Sump Pump
  • Duplex Oil Filters
 
Protection System
  • Fuel and Oil Shielding
 
Starting System
  • Air Starting Motor
  • Air Start Accessories
  • Electric Starting Motors - Single 24 Volt
  • Starting Aids
  • Battery Sets - 24 Volt - Dry
  • Dual Starting Motors (Electric and Air)
 
Packing
  • Engine Protective Cover
  • Export Packing
  • Storage Preservation
 
Mounting System
  • Front Support
  • Adapter Kits
  • Isolator Mounts
 
Power Take-offs
  • Front Enclosed Clutches
  • Rear Hydraulic Pump Drive
 
General
  • Fumes Disposal
 
Control System
  • Instrument Panels
  • CATERPILLAR ALARM AND PROTECTION
  • Fuel and Oil Shielding
 

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Share This Product