Cat C18 Auxiliary/Generator Set Engine (IMO II)

Cat C18 Auxiliary/Generator Set Engine (IMO II)

Cat C18 Auxiliary/Generator Set Engine (IMO II)

C18 auxiliary/generator set engines incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines also contribute to minimizing owning and operating costs. The IMO II compliant ratings are available with heat exchanger or keel cooled options. All major MCS type approvals are available from the factory.

Power Rating
Minimum Rating
404BHP
Maximum Rating
660BHP
Engine Specifications
Aspiration
TA, TTA
Rotation from Flywheel End
Counterclockwise
Bore
5.7in
Displacement
1106in³
Configuration
In-Line 6, 4-Stroke-Cycle Diesel
Stroke
7.2in
Dimensions & Weights
Height
51.2in
Length
73in
Width
44.6in
Dry Weight
1950lb

Standard Equipment:

Air Inlet System
  • Separate circuit after-cooled (SCAC)
  • Open Crankcase Ventilation (OCV) system
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection
 
Control System
  • Programmable low idle
  • Electronic diagnostics and fault logging
  • Electronic fuel/air ratio control
  • Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
  • 70-pin customer connector
  • Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA
 
Cooling System
  • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
  • Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
  • SCAC pump, gear driven, for HEX cooled engines only
  • Jacket water pump, gear driven
  • Auxiliary water pump, gear driven
  • Sea water pump, bronze impeller, gear driven
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
 
Exhaust System
  • 152 mm (6 in) round flanged outlet
  • Water-cooled exhaust manifold & turbocharger
 
Flywheels & Flywheel Housings
  • Flywheel Housing, SAE No. 0
  • Flywheel, 18 inch, 136 teeth
  • SAE standard rotation
 
Fuel System
  • Front service simplex fuel system
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design
 
Lube System
  • Front service simplex oil system
  • Center sump oil pan:
  • Front and top service oil filler locations
  • Front service dipstick
  • Oil pump, gear driven
 
Mounting System
  • Front support - adjustable
 
Power Take-offs
  • Hydraulic Pump Drive
  • Crankshaft Pulleys
  • Front Stub Shaft
  • Front Enclosed Clutch
 
General
  • Front damper guard
  • Front service engine
  • Common electrical bonding point
  • Engine does not ship with zinc components
  • NOTE: These engines are for constant speed generator set applications only, and NOT to be used for variable speed applications
 

Optional Equipment:

Exhaust System
  • Dry Elbows
  • Water-Cooled Elbows
  • Flexible Fitting
  • Flange
  • Muffler
  • Muffler Spark Arresting
 
Air Inlet System
  • Air Inlet Adapter
 
Charging System
  • Battery Chargers
  • Charging Alternators
  • Alternator Mounting Group
  • Ammeter
 
Control System
  • MECP I - Marine Engine Control Panel
  • Caterpillar Alarm and Protection
  • Load Sharing Attachment
 
Cooling System
  • Aux Expansion Tank Flange Kit
 
Fuel System
  • Duplex Fuel Filters
  • Fuel Cooler
  • Primary Fuel Filters
  • Flexible Fuel Lines
 
Instrumentation
  • Instrument Panels
  • OEM Wiring Harness
  • Gauges
  • Oil Level Sensor
 
Lube System
  • Duplex Oil Filters
  • Sump Pump
 
Power Take-offs
  • Crankshaft Pulleys
  • Front Stub Shaft
  • Hydraulic Pump Drive Adapter
  • Front Enclosed Clutch
 
Protection System
  • Marine Classification Society and SOLAS
 
Starting System
  • Electric Starting Motors - Single 24 Volt
  • Air Starting Motor
  • Air Start Accessories
  • Starting Aids - JW Heaters
  • Battery Sets - 24 Volt - Dry
 
Mounting System
  • Front Support
  • REAR ENGINE SUPPORT
 
Packing
  • Engine Protective Cover
  • Storage Preservation
  • Export Packing
 

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Share This Product