Cat C18 ACERT Propulsion Engine (IMO II)

Cat C18 ACERT Propulsion Engine (IMO II)

Cat C18 ACERT Propulsion Engine (IMO II)

The C18 ACERT marine propulsion engine has commercial application ratings of 454-715 bhp that meet IMO II & EU Stage IIA emissions regulations, and 469-715 bhp that meet EPA Tier 3, IMO II and EU Stage IIIA emissions regulations. In addition to the benefits the C18 ACERT’s advanced marine engine technology brings, you welcome aboard legendary Cat product support. No matter where your spirit of adventure takes you, rest assured the Cat Dealer Network is close by.

Power Rating
Power Range
454-715 bhp (339-533 bkW)
Engine Specifications
Speed Range
1800-2100 rpm
Emissions
IMO II, EU IIIA
Aspiration
TA, TTA
Bore
5.7in
Stroke
7.2in
Displacement
1106in³
Rotation from Flywheel End
Counterclockwise
Configuration
In-line 6, 4-Stroke-Cycle Diesel
Dimensions & Weights
Minimum Dry Weight
4000lb
Minimum Length
73in
Maximum Length
76in
Minimum Height
47.2in
Maximum Height
51.2in
Minimum Width
44.6in
Maximum Width
47.4in
Maximum Dry Weight
4299lb

Standard Equipment:

Air Inlet System
  • Separate circuit after-cooled (SCAC)
  • Open Crankcase Ventilation (OCV) system
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection
 
Cooling System
  • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
  • Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
  • SCAC pump, gear driven, for HEX cooled engines only
  • Jacket water pump, gear driven
  • Sea water pump, bronze impeller, gear driven
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
 
Exhaust System
  • Water-cooled exhaust manifold & turbocharger
  • 152 mm (6 in) round flanged outlet
 
Flywheels & Flywheel Housings
  • Flywheel Housing, SAE No. 0
  • Flywheel, 18 inch, 136 teeth
  • SAE standard rotation
  • SAE No. 1, Flywheel: 14 inch, 113 teeth
 
Fuel System
  • Front service simplex fuel system
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design
 
Lube System
  • Front service simplex oil system
  • Center sump oil pan: Deep; 500 hour oil change interval, Shallow; 250 hour oil change interval
  • Front and top service oil filler locations
  • Front service dipstick
  • Oil pump, gear driven
 
Mounting System
  • Front support - adjustable
 
Power Take-offs
  • Poly-V groove for alternator drive
  • NOTE: There are no standard power take-offs available
 
General
  • Front damper guard
  • Front service engine
  • Common electrical bonding point
  • Engine does not ship with zinc components
  • Engine is certified to D2/E2 emissions cycles
  • Certified to IMO II Marine Commercial Propulsion (E3) Cycle Emission Standards
  • Certified to EU Stage IIIA AND CCNR Stage II (E3 Cycle) Emissions Standards.
  • NOTE: Ratings listed below can also be used in Recreational / Pleasure Craft applications.
 
Control System
  • Programmable low idle
  • WOSR (Wide Operating Speed Range) available for EPA Tier 3 - B and C Ratings
  • Adjustable High Idle (TEL) - EPA Tier 3 WOSR Ratings Only
  • Electronic diagnostics and fault logging
  • Engine and transmission monitoring (speed, temperature, pressure)
  • Electronic fuel/air ratio contro
  • Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
  • Torque Limiting functionality for WOSR ratings only
  • 70-pin customer connector
  • Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA +/-
 

Optional Equipment:

Exhaust System
  • Dry Elbows
  • Water-Cooled Elbows
  • Flexible Fitting
  • Flange
  • Muffler
  • Muffler Spark Arresting
 
Air Inlet System
  • Air Inlet Adapter
 
Charging System
  • Battery Chargers
  • Charging Alternators
  • Alternator Mounting Group
  • Ammeter
 
Control System
  • MECP I
  • Caterpillar Alarm System and Protection
 
Cooling System
  • AUX Expansion Tank Flange Kit
 
Fuel System
  • Duplex Fuel Filters
  • Flexible Fuel Lines
  • Fuel Cooler
  • Primary Fuel Filters
 
Instrumentation
  • Instrument Panels: Marine Power Display, Color Marine Power Display, Color MPD Dual Display Harness, MPD Wiring Connection Kit
  • OEM Wiring Harness
  • Engine to Engine Harness
  • Gauges
  • Transmission Sensors
  • Oil Level Sensor
 
Lube System
  • Duplex Oil Filters
  • Transmission Oil Cooler
  • Sump Pump
 
Mounting System
  • Vibration Isolators
  • Front Support
  • Rear Support
 
Power Take-offs
  • Note: PTO Options Require Torsional Vibration Analysis
  • Crankshaft Pulleys
  • Front Stub Shaft
  • Hydraulic Pump Drive Adapter
  • Front Enclosed Clutch
 
Protection System
  • Marine Classification Society and SOLAS
  • Marine Classification Society and Fire Resistance
 
Starting System
  • Electric Starting Motors - Single 24 Volt
  • Air Starting Motor
  • Air Start Accessories
  • Starting Aids - JW Heaters
  • Battery Sets - 24 Volt - Dry
 

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Share This Product